The constant velocity (CV) boots can secure the joints from debris. It also keeps them from grease splatter or leakage. If you hear any noise while moving and turning your vehicle, it shows that your boot and CV axle need replacement. While replacing, always choose the best CV axles. However, if you do not hear a knocking or popping sound, this indicates a broken boot. Only CV boot replacement without removing axle can save your cost.
CV Boot Replacement Without Removing Axle
The following guiding steps will guide you regarding replacing CV boot kit. There are some extra tips with a few points for safety and security. Let us get started with the details of each step:
1. Remove the Wheel
First of all, use the chocks to secure the vehicle so that it may not move backward while working. Bring out your CV boot repair kit, and proceed to lift the vehicle by using portable hydraulic jacks from the side that need replacement. These jacks are present in the boot replacement kit.
To support the weight of the car, make sure you place the safety stands below it. Towards the end, allow someone to put pressure on the brakes. This will help you loosen the lug nuts by using the wrench.
- Lift the vehicle to a height that allows you to work properly.
- Never start working without safety stands.
- The location of the vehicle body frame to secure undercarriage.
- Take 2 turns to loosen lug nuts.
2. Cut Broken CV Boot
Start by removing the CV Boot Clamp. You will see that there is one on either side of the boot. Take out your boot replacement kit and start cutting the broken boot with the help of a box blade.
● Take precautions by cutting boot in opposite direction. This will save you from injuries.
● You can locate the boot clamp position by identifying the joint grooves.
3. Axle and Joint Cleaning
This step of CV joint cleaning requires you to take a bucket and place it where you are working. The grease will likely splatter. This practice will allow you to avoid staining the area.
Other than this, you need to wear gloves on your hands to avoid any damage. Safety goggles are also recommended by experts during such sensitive tasks. You can find a cleaner agent in your kit. Complete this step by removing the dirt and grease with the help of it.
● You can avoid stains by using a towel to remove residues.
● Rugs can also be used for the same purpose but you have to discard them immediately.
4. Install New CV Boot Parts
The first step of installation would be joint greasing. When you buy the CV boots kit, greasing packages come with it. Cut open these packages from one end and start applying on CV boot parts. You have to apply them on the joint and axel as well.
Proceed to the next step which involves the main installation. You will see that there are already cuts on the CV boot groves. All you need to do is to open them and place the boot part over the axle area. As you do it successfully, now take out glue from the CV boot kit. The application of glue will allow you to join both ends of the CV boot. After some time when the glue is completely dried, it will turn into an elastic rubber-like material.
Towards the third stage of the installation process, start greasing cv axle including the inside area of the new CV boot. You have to as much of it as possible so that there is no chance of future damage to the joints.
5. Placement of New CV Boot
After the CV joint boot repair and installation is complete, it is time to move the new boot to its right place. You need to know the shorter side of the CV boot come in contact with the axle shaft area, while the larger end goes with the outer joint area. If you try to observe, you will find out that there are grooves on both ends. These grooves are an indication that which side will fix with which area.
As this is done, the installation of clamps is the last step to complete the whole process. Take out the clamp pliers like Lisle 30800 Plier from the kit and install the metal clamps at their place. This is the last step of the boot replacement process.
In the end, get your vehicle tires back on the frame. You can do this by tightening the lug and axle nuts. After this, just lower the vehicle to its ground position. Also, remove the safety stands. Keep in mind that you have to remove the emergency brakes as well.
It is recommended by experts to buy a maintenance manual. This addition will help you carry out such tasks on your own, and alongside, you will earn a lot of things about your vehicle.
Tools Requirement for Replacement
Screw Driver, Torx Bit, Air Ratchet, Pliers, Strap Tool etc.
Cost of CV Boots Replacement
If you want CV boot parts need replacement with a good axle shaft like Cardone axle shaft, it will cost you between 250 to 300 dollars. However, the CV boot repair cost becomes an expensive proposition when the labor factor is also involved. The figures went up to around 550 to 650 dollars.
The cost of a replacement kit and related supplies varies between 15 to 30 dollars. So, if you have them, and you know how to replace boot kit without removing axle, then you have the chance to save a lot of money.
Try to get professional help if you feel unsure about the CV boot replacement without removing axle. New and complicated vehicles also require expert intervention to do the job. Therefore, never rely solely on your knowledge because maybe you are missing out on something. You can better learn from them to carry out the task later on. These are guidelines for those who are just starting to learn CV boot repair. By following the steps mentioned above, they will be able to replace damaged or broken CV boots at home.